Arcam P7 Instructions d'exploitation Page 7
- Page / 16
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
6
7
CONNECTING TO LOUDSPEAKERS
The speakers should be connected to the loudspeaker terminals,
as per the correct input signal. In other words, the Centre channel
speaker should be connected to the module that is being fed the signal
for the Centre channel, and so on, for all the channels.
As with all speaker connections, ensure that polarity is maintained
when connecting the speakers (i.e. red (+) to red; black (–) to black).
To bi-wire or bi-amplify your speakers, refer to the section towards the
end of this Handbook where diagrams are provided. If you are unsure
as to how your system should be connected, or need advice on bi-
amping, please consult your Arcam dealer.
Arcam P7 power amplifier
HF
LF
+
+
–
–
+
–
IN
OUT
+
–
IN
OUT
+
–
IN
OUT
+
–
IN
OUT
+
–
IN
OUT
+
–
IN
OUT
+
–
IN
OUT
HF
LF
+
+
–
–
HF
LF
+
+
–
–
HF
LF
+
+
–
–
... etc. ...
R surround
rear
R
surround
R
front Centre
L
front
L
surround
L surround
rear
Outputs from multichannel pre-amp (e.g. AV8)
I
CONNECTING TO A POWER SUPPLY
WRONG PLUG?
Check that the plug supplied with the unit fits your supply and that
your mains supply voltage agrees with the voltage setting (100V, 115V
or 230V) indicated on the rear panel of the unit.
If your mains supply voltage or mains plug is different, consult your
Arcam dealer or Arcam Customer Support on +44 (0)1223 203203.
MAINS LEAD
The appliance is normally supplied with a moulded mains plug already
fitted to the lead. If for any reason the plug needs to be removed, it
must be disposed of immediately and securely, as it is a potential shock
hazard when inserted into the mains socket. Should you require a new
mains lead, contact your Arcam dealer.
PLUGGING IN
Push the plug (high current IEC line socket) of the power cable
supplied with the unit into the POWER INLET socket in the back of the
unit. Make sure it is pushed in firmly.
The P7 has been designed so that a standard-rating IEC cable (which
has insufficient current rating) cannot be plugged into the P7. Only
high current power cables can be connected.
Put the plug on the other end of the cable into your power supply
socket and switch the socket on.
Basic wiring of loudspeakers (three channels omitted for clarity)
- Multichannel Power 1
- Amplifier 1
- Using this handbook 3
- Safety guidelines 4
- Getting started with your P7 5
- POSITIONING THE UNIT 6
- CONNECTING TO A PRE-AMPLIFIER 6
- CONNECTING TO LOUDSPEAKERS 7
- CONNECTING TO A POWER SUPPLY 7
- Operating your P7 8
- BEFORE YOU START 9
- BI-WIRING YOUR LOUDSPEAKERS 9
- BI-AMPING YOUR SYSTEM 9
- Troubleshooting 10
- FAULT STATUS INDICATORS 11
- Technical specications 12
- Guarantee 13
- SH100EIssue 1 16
Produits connexes et manuels pour Amplificateurs audio Arcam P7
(17 pages)
(16 pages)
(52 pages)
(86 pages)Xerox 5020V_U manuály
Uživatelské manuály a uživatelské příručky pro Multifunkční zařízení Xerox 5020V_U.
Poskytujeme 1 manuály pdf Xerox 5020V_U ke stažení zdarma podle typů dokumentů: Datový list
Commentaires sur ces manuels